Prochem Legend Gt / Oil Leak Very Bad
I have a Prochem Legend Gt bought in 2011 , the unit is 4 years old and has 2300 hours on it. I change the oil & filter every 100 hours like clock work. The machine has always run great. There has...
View ArticleNew Engine For My Truckmount?
I need you guys opinion on an engine that I have, I noticed a few months back oil was on my unit under the burner (Prochem 150). So finally took it to my regular mechanic, different mechanic could not...
View Articleauto pump-out problem
i have the in tank pumpout (the one in the blue box with screen on one side). it does not pump very well at all. if i have the machine idleing and no hoses on it pumps good but when i crank it up with...
View ArticleSuction
Please help! ! I prochem Saber 2000 model and can't get continuous suction. Hold hand over vacuum inlet and it builds up but drops when put vac hose to it.
View ArticleProchem Legend Temperature
I've been using this prochem legend se about a year now and when they replaced the heat exchanger, it went from 250F to 230F maximum heat temperature. I called the tech. who replaced my heat exchanger...
View ArticleClik here to view.
Prochem Legend Float Switch Troubleshooting? How To?
I finally got to run my Legend for 3 hours last night, and it really impressed me! But when I went out to the truck, it had blown water everywhere, because the float switch didn't shut it down. How to...
View ArticleProchem Performer Cub XL won't start
Please watch the video. Any suggestions I could try on my own until I take it to the shop. View attachment 60666
View ArticleProchem performer 405
Hey guys i have a question maybe someone can help us with. So our truckmount as soon as we turn the pump switch on watet is dripping out the exaust on the right side of the machine......we recently had...
View ArticlePROCHEMS-All models REPAIR archive---
65 75 75HE 100 100A 150 200 300 400 650HP 800A Bruin 1 Bruin 2 Cub Cub XL Bear Bear Cat Blazer Blazer XL Trail Blazer Legend Legend SE Legend XL Performer Performer 405 Performer 805 Peak Apex Everest...
View ArticleCub XL low pressure
Just bought a used Cub XL and after I got it running found that it has some water pressure but not a lot, maybe 150 lbs. The pressure gauge doesn't work so I can't tell. And the pressure can't be...
View Articlei have a prochem bruin ii and the chemical shows flow on prime but not when i...
I have a bruin ii and when I prime the chemical it shows full flow, also I have an open hose hooked up to a shutoff valve in my extra solution outlet, and when I open that the chemical shows flow, but...
View ArticlePerformer Bear
I have a performer Bear. Yes, I know it's old, but it runs like a scalded dog! When i shut it off and before I open the waste tank discharge drain., the waste water starts running out the front of the...
View ArticleValve on transfer pump
The valve on my tank that transfers the water to the cleaning unit is breaking. Can these tanks be welded ? And what is inside them ? Thanks for any help and have a great afternoon.
View ArticlePressure regulator problem
Pressure regulator on my Prochem Performer doesn't go past 700Psi. Does anyone know how to fix it? I still have plenty of oil in the pressure pump. I can easily change the pressure below 700, pressure...
View ArticleProchem will only run with choke open
Finally have my TM moved over to my new van got everything set up and for some reason my machine will only run with the choke open ? It has been ran very few hours over the last 3 months mainly just...
View ArticlePerformer 405 timing chain
Ok, so my P405 has this ticking & I'm pretty sure it's a loose/broken timing chain tensioner. Now I remember this engine from way back when I was a teenager in my Dat 521 P.U. but man try to find...
View Article03 Prochem Legend se excessive water pressure.
My Prochem Legend SE has excessive pressure. The pressure gage is stuck at 1500psi even with the machine off. If I connect a cleaning wand and start the machine the pressure overcomes the control valve...
View ArticleProchem Blazer Xl heat and vacuum loss... Help please.
Hi all, New guy here, I have a prochem blazer xl with nearly 1000hrs. The problem started a week ago with loss of vacuum and no heat when the machine is running. With the vacuum port's clear and...
View ArticlePutting new resin in a Prochem water softener
I think my water softener has needed new resin for a while. I have never been able to find a cheap, easy way to even tell if I have soft water. My machine doesn't seen to have hardly any scale related...
View Article