Very strong gas
Truckmount gas was very strong today ran for a while then shut off .Sprayed carb cleaner in it stop smelling strong for a minute then later it shut down what could be the problem Sent from my Nexus 7...
View ArticleVideo of truckmount shutting off less than 10min
Sent from my SCH-I545 using TMF Forums mobile app
View Articlechanged check valve . now not gettin pressure ....
had freeze . popped plug out . replaced bolt and flange that recieves plug/ check valve. no leaks no pressure .lost new 2 year owner. b with knowledged person tomarrow investigating problem. any tips...
View Article90's model Legend shutting off and overheating
This old Legend shuts down after 20 to 45 minutes of cleaning while set to high temp and overheats. As I approach machine I hear a clicking noise that is louder than the normal fuel pump sound. As I...
View ArticlePerformer 405 Carb.
Does anyone know exactly what make and model the carburetor on the Performer 405's Nissan A12 motor is? $500+ for a new one and I'm looking for options. Aaron
View ArticleProchem Blazer help again
Blazer ran for 2hr today after that shuts off now only runs for 5 to 10 minutes and shuts off even after it cools down Sent from my Nexus 7 using TMF Forums mobile app
View ArticleNeed New Kohler engine for Prochem Legend
I was told that the replacement engine is for my original 8 thousand hour 90's engine is the new 20 HP Prochem model #40-902152. I just hope this is the correct one. I was quoted 3200 by Jon Don and...
View Articlechemical pump leak
when I turn my chemical on it leaks, the brass elbow seems to be tight that is connected to my line going to flowmeter and that's were I have my leak is by elbow. any thoughts?
View Articlepump out question/locked up?
my waste tank float switch went bad. I bypassed switch to see if I had any other problems. been bad for almost a year and haven't used pumpout. so in process of bypassing to get juice to pump out all I...
View ArticleGrease
Found grease on the floor of my van today cannot figure out where it's coming from but it's really sticky I got some of it up before I sent the picture but made you guys can figure it out. Sent from my...
View Articlepumpout switch question
as earlier posted my pumpout switch is bad, do I need the whole switch assembly or just the switch magnet housing? don't want to buy what I don't need, thanks again guys!
View ArticleWater box for Performer
Hello, I am looking to replace my rusting aluminum waterbox with a plastic one. Does anyone have a used box or know where to buy one online? I could call Prochem but that's probably a super expansive...
View Articlethrottle control arm for prochem legend
I have a 22hp prochem legend today while cleaning the choke linkage and throttle arm came loose..I was able to attach one side but can't tell if the other end has broken or if it can be...
View ArticleProchem peak overheating
My buddy is having trouble with his Prochem peek over heating from the Kohler water cooled engine. Blowing boiling water back into the overflow box. Belts are good, new pressure regular ( top and...
View ArticleLegend sounds louder
I have 2400 hrs on my legend xl and it seems to be louder than it use to be to the point were customers are commenting on how loud it is. What are the common issues with this machine with it getting...
View ArticleI want to put a silencer on my Everest 650hp, what's the best configuration?
Anybody running a silencer on Their machines? What configuration do you suggest? Their is no room inside the unit so need to get creative here. Any help would be appreciated
View Article25 Kohler issues replaced coil. No dice. Need help
It started out when the truck was running on half power I tested it and replaced the bad coil I still have half power. There is spark on the side that was bad but it still dies when I remove the good...
View ArticleProchem performer 405
I recently found a refurbished prochem performer 405 for sale with 3000 hours on it. The price was 12,500 with a 30 day warranty. Is this a fair price for this tm ?
View Article