Broke Prochem Hard Surface Edging Tool
I was trying to remove the clogged tip and twisted the fitting off the little tube. Prochem doesn't offer a replacement part. Two different distributors and Prochem can't give me any advice on how to...
View Articlewater box overflowing
put new seal 0n piston end, put water valve back together and valve is still leaking. is it common for valves to need replaced? Would i need new piston also when getting new valve or does it come with...
View ArticleChanging Anti-Freeze On A Prochem Apex
Anyone know the steps in changing out the antifreeze on an apex? Also do you use just regular 50/50 ? Thanks
View ArticleProchem battery dies quickly
I have bought my 3rd battery in like a month for my Prochem legend SE ..Installed it and the next day it is dead ..Nothing is left on and the key is turned off . It drains it so much I have to crank my...
View ArticleWater was leaking from here help
View attachment 23763 View attachment 23764 Sent from my iPhone using TMF Forums
View ArticleProchem. 405 heat exchanger just popped
The heat exchanger started leaking like sieve. Makes me mad cause we kept the heaters on the vans so I suspect it was a stress crack from former owner. Anyhow I'm going to make a retro fit heat...
View ArticleCAT PUMP CLUTCH NOISE ON LEGEND
Hi, I have a legend with the cat 3CP1140 pump. Yesterday, I started it up and it started making a loud metallic scraping noise. If I turn the stator on the front of the clutch by hand it is scraping...
View ArticleLegend leaking water out the vacuum port over night.
When I come out in the morning, there is water dripping from the vacuum port. Also, the machine is only running about 160-180 with 100 ft of hose. I've taken the auto bypass out and cleaned all that,...
View ArticleProchem Performer 405 Immediate shutdown once override sw is released?
We use a Prochem Performer 405 and have had little to no problems over the last few years of use. As of yesterday during startup after holding the water/oil override switch to the left during start up...
View ArticleGood guide for troubleshooting bypass system Performer, Bruin II, Legend
I found this trouble shooting guide that looks like it could be really helpful if you own one of the above units. Thought it was worth putting on here....
View Article$650 For A Radiator Man WTF?!!! Prochem Performer
So im cleaning my Mom's house and i notice antifreeze on the floor of the van. Ends up I had a slow leak in the radiator. Called the supply house and was quoted about $650 for a new one! Holy crap are...
View ArticlePerformer 405 Vacuum
Good morning. I just bought a Performer 405 with 3100 hours on it. I replaced a cracked carb which I figured would improve vacuum. It did a little but it just doesn't seem like I have 405 cfm. This is...
View ArticleProchem Peak Heater Cores
Looking at purchasing a Prochem Peak. It has 2 heater cores located at the bottom of the machine. one is copper and the other stainless steel. Can these be fixed more the stainless steel heater coil?...
View ArticleDiscountTruckmounts.com
Has any ever worked with this company and is this a good deal? http://www.discounttruckmounts.com/TRUCK-MOUNTS-FOR-SALE.html A Prochem 405 rebuilt for $12,900 with fresh water tank and new hoses? Thanks
View ArticleProchem blazer shuts off
Blazer shuts off in the middle of a job today I had a1/2 tank of gas could that be problem? Anything else I need to search for. Also do these shops have diagnostic machine to check everything ? Sent...
View ArticleProChem APO motor #40-902151
I purchased a prochem apo online using this motor. It came in leaking oil out the rear of the motor near the brushes. I purchased a new motor at a discount because the 'dealer' refused to honor the...
View ArticleProchem blazer
Maybe you can guys can solve my problem before it goes to the shop.ok start my truckmount let it runs for about 15 minutes then shut off the truckmount hook the solution hose up now the truckmount...
View ArticlePressure line pulsating
I have a Pro Chem performer. I noticed that my pressure line is pulsating pretty bad. Pressure is good. Are the accumulators rechargeable? Is there any way to fix this besides getting an ass ramming...
View ArticlePerformer does not keep heat
Did all the following still dumps water into waste tank. When I turned the thermostat up my pressure would go up about 50psi.Any other thoughts. Testing the bypass system for proper operation should...
View Article